There are many reasons why you would opt for a table saw. Table saws are ideal for professional woodworkers who do not want to spend most of their time sawing wood by hand. When choosing a saw, most people tend to want the original saw because the regular handsaws are cheaper. However, it will take a longer time to saw a single piece of wood.
The other aspect relates to dealing with muscle soreness. Sawing wood pieces day in and day out with the traditional handsaws will lead to the Delayed Onset Muscle Soreness (DOMS) condition. After that has happened, the quality of your work will profoundly reduce. This guide should help you buy the best table saw blade in the market.
- Best Jigsaw Blades for Plywood/Hardwood/Stainless Steel: 2019 Reviews and Guide
- Circular Saw Vs. Jigsaw Vs. Reciprocating Saw: Get The Right Tool For Your Job
- Best Circular Saw Blade for Plywood/Hardwood: 2019 Reviews and Guide
- 1 Top 7 Best Rated Table Saw Blades for Cutting Hardwood/Plywood/Oak
- 1.1 Forrest WW10407125 Woodworker II 10-Inch 40 Tooth ATB-125 Kerf Saw Blade
- 1.2 Freud 10” x 40T Next Generation Premier Fusion General Purpose Blade For Crosscut
- 1.3 Oshlun SDS-0630 6-Inch 30 Tooth Stack Dado Set with 5/8-inch Arbor
- 1.4 Freud 10”x50T Thin Kerf Combination Blade (LU83R010)
- 1.5 Oshlun SBJ-0830 8-Inch Box and Finger Joint Set
- 1.6 Dewalt DW3106P5D601 Series 20 10-inch 60T Fine Finish Saw Blade
- 1.7 Freud 10” x 24T Heavy-Duty Rip Blade (LM72M0010)
- 2 Essential Factors to Look for the Right One
- 3 How thick/wide Are They?
- 4 Can Table Saw Blades be Sharpened?
- 5 How Long Do They Last?
- 6 What Direction Does Table Saw Blade Turn?
- 7 When and How to Replace the Blade
- 8 FAQs:
- 8.1 Q: Why do I experience burning of the wood when ripping?
- 8.2 Q: Why do I get vibrations each time my saw reaches the maximum RPM?
- 8.3 Q: Why do materials chip out near the end of the cut when cutting laminated boards?
- 8.4 Q: Why are my cuts wider than the saw’s blade kerf?
- 8.5 Q: Why do my laminated panels chip on sheet’s bottom?
- 8.6 Q: What causes broken tooth?
- 9 Final thought
- 10 How useful was this post?
Top 7 Best Rated Table Saw Blades for Cutting Hardwood/Plywood/Oak
|Forrest WW10407125 saw blade||- Durable material
- Weight: 2.2 pounds
- It cuts smoothly
|Freud 10” x 40T saw blade||- Vibration-free design
- 30-degree Hi-ATB teeth
- Smooth and chip-free
|Oshlun SDS-0630 saw blade||- Weight: 6.3 pounds
- Vibration free
- High-quality carbide
|Freud LU83R010 saw blade||- Weight: 1.8 pounds
- Anti-vibration design
- Limited lifetime warrant
|Oshlun SBJ-0830 saw blade||- Two blade set
- Higher tooth count
- Material: professional-grade C-4 carbide
|Dewalt DW3106P5D601 saw blade||- Weight: 3.3 pounds
- Faster-cutting action
- 10-inches cutting diameter
|Freud LM72M0010 saw blade||- 24 teeth
- Laser-cut teeth
- Material: TiCo Hi-Density Carbide
Forrest WW10407125 Woodworker II 10-Inch 40 Tooth ATB-125 Kerf Saw Blade
Forrest has been producing saw blades since the 1980s, and most experts recommend their blades. Apart from the excellent rate cutting speed, the Forrest WW10407125 saw blade has 40 teeth and a thin kerf. The product also has a 10-inches diameter, which means that the cutting pace will be very fast.
Most woodworkers would not shell out a lot of their money to get a single blade, but the Forrest WW10407125 blade is worth it. First things first, when doing rip cuts and cross cuts on scrap wood pieces, such as red oak pieces that are lying in your tool shed, you will marvel at the unbelievable smooth finish.
Apart from being a great performer, the manufacturer uses high-quality material to make it. That means you should expect fewer wobbles, jumps, and vibrations. The blade also does away with bottom splintering, particularly on radial crosscuts. The 30-degree tooth style stops on demand to lessen chances of accidents or excessive cutting.
The key features
- The product weighs 2.2 pounds
- The material is carbide
- The product comes with a 30-day paid trial. If you are dissatisfied for any reason, you can opt for the return and refund option.
- It cuts smoothly
- Provides splinter-free wood results
- The material is durable
- The product has 40 carbide teeth
- The blade’s operation is relatively fast
- It will stay sharp for many years
- The product may struggle with thicker wood
- It also causes burn marks on wood
With 40 teeth, the blade does a great job when it comes to tearing through various types of wood not exceeding 8/4 stock. Apart from lasting for many years, the blade has other useful features such as the 0.125 kerf that reduces wasted wood.
Freud 10” x 40T Next Generation Premier Fusion General Purpose Blade For Crosscut
When looking for a sturdy saw blade, the Freud brand will always show up on your list. The 40 Teeth Next-Generation General Purpose Blade also provides us with a reason to recommend blades from the brand. It highlights the Trio Tooth Geometry from the brand wherein it starts with 30-degree HI-ATB grind situated at the top of every tooth. On its sides, you are likely to notice the double grind and the Axial Shear Face Grind on every tooth.
After combining the features, the manufacturer managed to produce a package that reduces amp draw by around 35 percent. Even more, the speed at which this blade eats through wood is 30 percent higher compared to that of the traditional table saw blades currently in the market. Features like TiCo High-Density Carbide and Perma-Shield non-stick coating ensures durability and long life.
The key features
- The product weighs 2.2 pounds
- The manufacturer uses carbide to produce it
- Comes with a limited lifetime guarantee
- With the 30-degree Hi-ATB teeth and double-sided tooth geometry, the product delivers smooth and chip-free
- It has a vibration-free design
- It is among the laser-cut blades on the market
- The manufacturer coats it to prevent vibrations
- You should expect minimal warping with time
- It is not the best table saw blade for rip cutting tasks
- The blade cuts unevenly when working with some types of wood like poplar and cherry
The product is an ideal choice for people in need of versatility. The product can crosscut and rip, and it will, therefore, help you complete most of your woodcutting tasks without changing anything. It is also durable.
Oshlun SDS-0630 6-Inch 30 Tooth Stack Dado Set with 5/8-inch Arbor
The Oshlun SDS-0630 30 Tooth Stack Dado Set provides several tables saw blades. It is, therefore, a convenient saw package if your woodworking projects involve different types of wood. It features two outside saw blades of 1/8- inch by 30 teeth, six life-sized five tooth chippers, and eight brass shims.
The shims come in pairs and range from 0.005 inches to 0.020 inches increment. The tooth chippers design is one 3/32 inch, four 1/8 inch and a single 1/16 inch plates.
During operation, you should expect little to no vibrations. At least, the plates will not fly across your room, and you will not see any signs of wobbling. The blades in the set cut wood with little effort, which is a great benefit to most woodworkers.
The key features
- The blade’s package weighs 6.3 pounds
- The blades design material is carbide
- Comes with a lifetime warranty, which does not cover tear, wear, and improper usage
- It is vibration free
- With the many types of blades in a single package, the product presents flexibility
- All the blades cut well with little effort
- The blades are vibration free
- The manufacturer uses high-quality carbide to make all the blades
- It might produce splinters when working with some types of wood
The Oshlun SDS-0630 is an excellent addition to any woodworker’s bench. Variety of blades means that you can select the right one for every project. The producer also uses high-quality C-4 carbide to make all blades. You should, therefore, expect durability and longer life.
Freud 10”x50T Thin Kerf Combination Blade (LU83R010)
With a different price and ability to saw through various pieces of wood, the Freud LU83R10 Table Saw Blade has separated itself from the other blades already on the market. You do not have to break the bank to buy this blade, which delivers awesomely smooth cuts.
The Freud LU83R010 produces top-notch quality and performance. For example, the manufacturer uses heavy-duty materials, which provide lesser power during woodcutting operations. Therefore, the sawing is not only fast but also the cuts are smooth. The product rips through chipboards, plywood, and laminate.
The key features
- The product weighs 1.8 pounds
- Comes with a limited lifetime warranty
- The manufacturer arranges the 50 tooth in groups of five
- Has a balanced design
- An ideal choice for people who mostly cut through crosscut wood
- Features an anti-vibration design
- Remains stable including when under heavy loads
- Has an ability to minimize friction and heat
- It is reasonably cheap
- It is not the best choice when cutting thick wood pieces
The manufacturer makes the Freud LU83R010 Blade with laser-cutting technology. The blade is therefore vibration-free. Moreover, with the impressive features, you might think that you need lots of cash to buy it. That is not the case. The product is cheap. It is always stable including when under heavy loads.
Oshlun SBJ-0830 8-Inch Box and Finger Joint Set
The Oshlun SBJ-0830 is available as a finger joint and two-piece joint piece designed for hobbyists and professionals interested in box joints. Each of the two blades has 30 teeth designed to make square notches and smoother fingers. The manufacturer has designed it for use on a 3/8-inch box and 1/4 –inch box joints. That alone makes it a versatile blade – that is because the two joints are the most popular.
Each tooth on the blade boasts C-4 micro-grain tungsten carbide tip with edge retention. It easily cuts through softwood, hardwood and various wood materials without leaving stains. The manufacturer provides you with a storage case and an instruction manual to help you get started. Most users praise the product for the flat-bottomed notches and perfect square fingers.
The blade spins at around 7000 RPM. It is suitable for people who want to add blades to their existing sets. To switch from the 3/8-inch to ¼-inch, you need to reverse the outer blades and inner blades.
The key features
- Material for design is professional-grade C-4 carbide
- Comes with a two blade set
- The manufacturer offers detailed setup instructions
- Has ground carbide tips for cutting precision
- Comes with a storage case
- The manufacturer uses professional grade C-4 carbide material to make the product
- The high-quality c-4 carbide tips retain the edge for long periods
- The product has higher tooth count for accurate cutting
- Works with various types of table saws
- You will only have two blades for the price
The product is suitable for individuals desiring to make smooth fingers and box joints. It easily cuts through hardwood and softwood and leaves no stains. To start using it, you have to read the user’s manual.
Dewalt DW3106P5D601 Series 20 10-inch 60T Fine Finish Saw Blade
Whenever you are planning to crosscut within a short time, the Dewalt DW3106P5D601 should be among your top few choices. It features 60 teeth, which reduce noise during operation. Moreover, due to the thin kerf, you will always get faster and smoother cutting operation.
The product is available in a two pack that will be helpful during woodworking. The manufacturer computer balances the plates for accuracy and faster smooth cuts. The wedge shoulder design also plays an important part in the preciseness. On the downside, the yellow paint transfers to the wood when cutting fast.
- Features thin kerf for smooth and faster-cutting action
- The manufacturer computer-balances the plate to reduce vibrations for preciseness
- The wedge shoulder design increases durability and accuracy
- Weighs 3.3 pounds
- Has a 10-inches cutting diameter
- The venting minimizes noise during operation
- Due to the thinner kerf, you should expect a fast operation
- Due to the many teeth, the product works great when crosscutting
- You are likely to encounter kickback problem
- The yellow paint transfers to wood, and you might, therefore, need to sand it off
The Dewalt product is suitable for people who want to complete their wood cutting tasks fast. If you mostly cut across the grain, the product is a great choice.
Freud 10” x 24T Heavy-Duty Rip Blade (LM72M0010)
Without the right table saw blade, you will hate your woodworking job when cutting boards along the grain. The 24-tooth Freud blade is a good option if you need to make the long tricky rips easier. Freud designed the product purposely for rip cutting. As a result, they hooked and flattened the teeth to deliver smooth finish on hardwoods when cutting.
The flat teeth are extra-large. They will cut almost any type of hardwood at a faster rate. The manufacturer also laser-cuts the teeth to ensure that the leading edges of this blade remain sharp and strong for a longer time.
If stored in the wrong places, the blade can rust. Store it in a dry place after you are finished with a project. The blade also cuts in unstable fashion when working with some wood. It might wobble slightly when cutting some types of wood.
The key features
- Has a 10 inches diameter
- Has 24 teeth
- Features Flat Grind, 126-inch Kerf, 5/8-inch arbor and 20-degree hook angle
- It is made of premium TiCo Hi-Density Carbide Ripping Blend to ensure maximum performance
- Has extra-large flat teeth design that facilitates smooth cutting
- the blade features laser-cut teeth
- the manufacturer designs the 24 teeth for ripping through various types of wood
- the venting system reduces noise effectively
- The manufacturer coats the blade to fight corrosion and pitch, but you should expect rust
- The carbide teeth chips gradually
The LM72M0010 table saw blade features 24 teeth designed to cut through tough woods. Therefore, it is a good option for individuals who cut with the wood’s grain most of the time. For long-term use, the manufacturer laser-cuts and strengthens the teeth. However, you should remember to keep this blade away from moisture to prevent rusting.
Essential Factors to Look for the Right One
Unless you know what you are exactly looking for, you might always up buying the wrong blade. Table saw blades are among the most important tools you will have in your woodworking collection.
Here are the key factors to consider when shopping for a blade.
Table saw blades are available in four basic types: flat top grind (FTG), alternate top bevel (ATB), a combination of FTG and ATB (ATBR) and triple chip grind (TCG). Even though the manufacturers make the blades for table saws, they have different sawing styles and designs. The type of blade you select will determine how you cut wood. In other words, every table saw blades produces different results.
Laser cut plates
With technology advancement, most manufacturers are now implementing laser-cutting technology when producing table saw wares. Due to the technology, most of the saw blades on the market are sturdier.
Manufacturers are also able to process blades further than the normal ones. That means that the blades are flat and remain vibration free when cutting wood. That is what every professional woodworker would want.
Geometry of the tooth
Most producers of saw blades employ varying combinations when creating blades. As a result, saw blades have varying shapes and designs that produce varying results. A quick example: by combining a certain blade’s angle and profile, they can produce saws that can offer cleaner cuts. Another style may offer a durable finish than the other types of table saw blades.
Power and size
Blades are either 6 or 8 inches, with 8 inches blades offering deeper cuts. Therefore, 8-inches blades require powerful saws, such as contractor saws and cabinet saws, to function. On the other hand, 6-inch saws work perfectly on various types of table saws regardless of the power. Select a blade with speed that matches that of your table saw.
The “insert plates” is the space where saw blades protrude from. When searching for a table saw blade the factor is an important consideration. Customized insert plates also come in handy.
Manufacturers build table saw blades in several variations, which is not the case to expect with other types of blades. Therefore, you have to understand the specifications of the table saw blade you are looking for. The specifications related to the Teeth per Inch (TPI), the material and the hook angle. 
How thick/wide Are They?
The thickness of a saw blade, known as “kerf,” refers to the depth of the slot the saw blade cuts, but some people use it to refer to the blade’s thickness. The width profoundly affects the cutting, power consumption, cost and the amount of wood you will lose when processing. Kerf is usually wider than the table saw’s blade plate.
Producers measure the kerf in thousandths of a single inch. Therefore, a full kerf blade can have a thickness of 1.110”. Some heavy-duty blades have 0.172” or 0.125”. A saw blade that is thicker than the recommended will rotate at a slower speed.
Can Table Saw Blades be Sharpened?
Yes. However, improper sharpening will cause problems. Also by sharpening the blade, you will be removing the material and as a result change the relationship between critical angles. If you are using a steel blade, you can use a round file to sharpen it. However, if you are using those with carbide-tipped teeth, you will need professional help.
How Long Do They Last?
A quality table saw blade should last for several years, but that highly depends on the level of usage and the woods you cut. Your blade might last longer if you work with easier cutting wood such as oak most of the time. When using the saw to cut Tough wood like hickory, cherry, and maple, you should expect a shorter lifetime.
What Direction Does Table Saw Blade Turn?
The blade turns clockwise toward the person feeding wood material. Table saws that rotate anticlockwise are uncommon. Therefore, you should never stand directly behind your saw when feeding material through. Stand slightly off to one side with the shoulders angled.
When and How to Replace the Blade
You should replace the blade after it is dull. Some of the things that will tell you that your blade is dull include binding, tearing and chipping the substance more than usual, and burning the wood. A sharp blade allows you to push the material forward with less effort. If you are forcing it, it is time to replace the blade.
To replace the blade, start by turning off the power and unplug the saw from your wall socket. Proceed and remove the blade plate. Most manufacturers use two screws to secure the blade plate. So, you will have to lose and remove them.
Place a small wood block against your blade to prevent it from turning accidentally. Turn the nut counterclockwise using a wrench and remove it from the blade. Put the blade away and proceed with installation of the new one.
To do that, you have to place the nut and the washer in place and secure your new blade by tightening them with a wrench. Use a wood block to hold the blade in place. Use a screwdriver to reinstall your blade plate. 
Q: Why do I experience burning of the wood when ripping?
A: There are four main reasons why you experience that. You might have aligned your table saw improperly with the fence. The blade might be heeling, or the cutting blade might need sharpening. Lastly, the stock might have shifted off the axis when cutting.
To eliminate the problem, replace the blade or have it sharpened and start using a feather board. Feed wood at a uniform rate. If you need excellent results, use 50-tooth blades.
Q: Why do I get vibrations each time my saw reaches the maximum RPM?
A: That might be an indication of an improperly mounted blade or unclean collars and arbor. Ensure that the arbor is not bent and it is running true. Check the drive belt to ensure that there is no slippage.
Q: Why do materials chip out near the end of the cut when cutting laminated boards?
A: That is usually a result of improper alignment of the cutting blade to the fence. It might also result from poor spindle bearings and arbor. To support the material on the bottom, you should have a close-fitting throat panel.
Q: Why are my cuts wider than the saw’s blade kerf?
A: That might be a result of the blade’s alignment to the fence. Remember to feed every material parallel to your blade.
A: If that is happening, it possibly means that you selected the wrong table saw blade. When working with laminated panels, you should go for negative rake saw blade with 3/8-inch tooth spacing.
Q: What causes broken tooth?
A: That might occur when your blade set is very high. Set the blade so that the central blade gullets clear the workpiece top. The consistent speed of the hook will also help reduce chances of a broken tooth.
Table saw blades are essential in any woodworking station. They help you saw wood of any type in lesser time. You need to turn the machine and feed your wood pieces into the rotating blade. Most of the blades in the guide are long-lasting, and you will, therefore, cut wood for many years to come.
We hope you not only enjoyed reading this blog article on the best table saw blade, but, we also hope you learned a few things as well. While you are here could you leave us a comment and let us know how we are doing. If you have any questions or concerns, please leave us a message.
Kindly share our blog on your social media to help us spread the knowledge we all share on this blog. Thank you for taking the time to read our work.
How useful was this post?
No votes so far! Be the first to rate this post.